EZ Pass windshield dots are mounted on most windshields of cars. Among them, lots of black dots appear on the edge of the windshield.

In addition, an EZ Pass attached near the rearview mirror is also noticeable. What do these do? Desplazarse hacia abajo para más detalles.

What Are EZ Pass Windshield Dots?

Then itll deduct the toll amount from your credit or bank account.

Explanation of E-ZPass and Windshield Dots

Windshield dots, also known as frits, are designed with the big-sized dots in the upper edge zone and decrease in size when moving towards the outer.

It helps to relieve pressure caused by high or low temperatures.

The expansion of the glass when it is too hot and the contraction of the glass when it is too cold will be balanced and controlled by these black dots.

So you can see that there is no relation between these black dots and the E-ZPass tag, considering their distinct purposes.

But people call them the E-ZPass windshield dots maybe because this zone is where drivers usually attach their E-ZPass tags.

How To Install EZ Pass?

If the window in the car is shaded, you need to ensure that the equipment is placed at least 1 inch below the shaded area.

2. Roof Mount

You can also stick the tag on the roof mount of the car. Some installation notes include the sticks position at least 3 inches from the cars roof.

Also, you shouldnt install it near radio antennas as it will interfere with the toll collection device when scanning the chip.

There are 4 adhesive strips on the E-ZPass tag. 2 are mounted on the tag, and the remaining strips are attached to the windshield.

After removing the protective backings from the adhesive strip, you should stick them in place and hold them for about 15-30 seconds to ensure the tag is firmly adhered to the windshield.

To keep the transponder on the windshield for a long time, you shouldnt remove them and re-glue them many times.

It will lose the adhesive over time and cause the tag to come off the windshield quickly.

3. License Plate Mount

The license plate mount is also a convenient location to equip the E-ZPass.

However, in addition to sticking the tag with glue as on the windscreen, you should use bolts to fix it on the license plate holder.

It helps the tag to be more firmly fixed and makes it difficult to fall off during driving, especially on bumpy roads.

In addition, after a period of exposure to smoke and dust, the adhesive will disappear and cause the transponder to fall off the vehicle.

Thus, you should use bolts to secure it right to the license plate. It is best to place it in the center of the front bumper to avoid the tag covering your license plate information.

How To Put EZ Pass On Windshield?

One of the most important steps when installing the EZ-Pass is cleaning the windshield.

The glass full of dirt or water will make the transponder stick better and have a longer life when sticking to the windshield.

If you let the cars inside wet without treatment, frost will mask the inside of the windshield , preventing the adhesion of the tag to the glass.

Identifying the front and back of the tag is easier because the manufacturer already has markings for the strips attached to the tag.

You should not use tapes of different types than those provided by the manufacturer because it may prevent the tag from sticking on the windshield for a long time.

Preguntas frecuentes

Besides, the battery can have problems when the vehicles glass temperature is too high due to prolonged exposure to the sun.

If this error is repeated many times, you should have a new E-ZPass transponder.

Another reason the EZ Pass doesnt receive a signal at the toll station is frost on the windshield. Its best to put a towel on the windshield to prevent frost when you leave your car outdoors and dont use it.

Conclusión

Overall, EZ Pass windshield dots are used to distribute heat evenly on the windshield to help prevent glass breakage.

Meanwhile, the EZ Pass tag or transponder is installed as an electronic toll collection device, so they are worlds apart.

Esperamos que este artículo le sea útil. Thank you for your time, and see you in the next posts.