Drive Start Control Malfuncția este o problemă pe care orice șofer Toyota o poate experimenta.

Într -o zi, Toyota DSC nu mai funcționează și trebuie să încercați să controlați viteza și să evitați pedalarea greșită a acceleratorului. Ce cauzează problemele DSC? Să ne urmărim pentru a găsi răspunsul.

Ce înseamnă defecțiunea Controlului Start Drive?

Drive Start Control Malfunction este o nouă tehnologie automată inventată de Toyota. Este conceput pentru a preveni accelerația neașteptată .

This system helps to ensure the drivers and the traffic participants safety when a speed problem arises and avoids restarting the engine while on the journey .

The main task of this special feature is to monitor the gear changes while driving and notice if they are accidentally pressing the gas, causing the car to go too fast.

Dacă detectează că viteza de conducere este prea mare, lumina de avertizare de defecțiune a controlului de pe tabloul de bord va clipi.

Sistemul va reduce automat puterea și accelerația motorului pentru a asigura siguranța.

În plus, ajută la detectarea obstacolelor care blochează drumul înainte și obstrucționează vizualizarea șoferilor. Apoi, sistemul reduce automat puterea motorului și frânele în astfel de cazuri.

Care sunt cauzele tundrei de defecțiune a controlului de pornire a unor drive?

Aceste erori nu apar întotdeauna atunci când sistemul este nou instalat, dar apar atunci când funcționează de ceva vreme.

Greșeli de conducere

Problemele de conducere sunt principala cauză de defecțiune în controlul pornirii de acționare. Poate fi derivat din factori subiectivi sau obiectivi.

Cu alte cuvinte, este afectat de șofer sau de alți factori externi, cum ar fi obstrucțiile, starea de spirit a șoferilor, etc.

Dacă șoferul ține simultan acceleratorul și schimbă echipamentul, va apărea Toyota ChR.

Motivul este că acest lucru a încălcat mecanismul de lucru al angrenajelor, care sunt schimbate într -o direcție care intră în conflict cu angrenajul auto.

Mecanismul de funcționare a mașinilor, care respectă un singur angrenaj, a fost rupt și a provocat o problemă.

Al doilea motiv este din cauza obstacolelor de pe drum. Uneori, călăreții vor întâlni găuri sau roci mici.

The system will not detect it because its disadvantage is that it can only spot obstacles with a large surface area, such as cars, walls, trees, etc.

Thus, when you accidentally slip into potholes, you panic on gear but forget that you still hold the accelerator, inducing the system to fail.

Siguranță problematică

O cauză comună a unei siguranțe suflate sau arse este un fir de siguranță liber și suflat.

The fuse makes it unbearable and burns when subjected to an overload current. It causes all systems to stop working automatically.

Though it is rarely the main reason for a Drive Start Control issue, some switches are directly tied to battery or core motor system elements.

The control system may fail if the defect is located inside these capacitors.

Rusted Connector

The connector is connected to the motor, mainly in charge of performing the braking function.

It mostly operates in emergencies when you press the brake pedal, and the throttle may or may not be pushed.

Overtime, debris will accumulate on the connector and leave rust. The cable terminates in particular sensors directly connected to the cars engine and synchronizes the pedal pressure based on the gear.

Due to this rusty level, it is harder for the Drive Start Control to carry out the function smoothly. As a result, the system may potentially fail.

How To Fix Driver Control Malfunction?

Once you find the cable is broken or open, you should go to the car repair shop.

The mechanics will solve it for you because the cable network below this engine compartment is quite complicated. If you are unfamiliar with cars, it is best to ask the auto mechanic to fix them.

Clean The Connector

As mentioned above, the connector is rusted or covered with dirt after a long time when the car has not been cleaned, which will trigger the Drive Start Control to fail.

So it would be best to have this connector cleaned carefully.

One thing to note is that after cleaning, you should leave it in the air for a while and then put it back in the right place.

The reason is that it may contain residual moisture after cleaning the connector that can cause connection problems.

After cleaning, the connector will communicate signals to the engine unit more quickly via sensors.

Consequently, the system can distinguish between forward and backward ratios even when you mistakenly leave the pedal pushed.

As a result, the possible malfunction of the Drive Start Control system is greatly reduced.

Use Clearance Sonar System

This technology can solve the problem of accidental acceleration. It helps to reduce the number of traffic accidents and collisions caused by a brake error.

Although currently, this sensor technology can only detect obstacles at close range, Toyota strives to improve it so that it can identify obstacles at a greater distance to contribute to traffic safety in the future.

Întrebări frecvente

When this part is faulty, it will not sense the surrounding obstacles, causing problems for careless drivers.

In addition, when the driver mistakenly steps on the brake pedal for the accelerator, a damaged DSC system will not be able to control this.

Serious incidents such as hitting pedestrians or crashing into electricity poles and trees can happen.

Especially for drivers who drive long distances or drive at night, not having this assisting system will be a challenge for them.

Concluzie

Overall, driver mistakes, problematic fuses, and rusted connectors cause Drive Start Control malfunction .

You can fix it yourself by checking the cable, cleaning the connector, or having the mechanics fix it.

Thank you for taking the time to read this article.

Hope you have received useful information.