L'allumage sans clé acquière une énorme réputation parmi les conducteurs grâce à sa modernité et à sa commodité. Cependant, certaines personnes préfèrent toujours le modèle classique qui utilise le système sans clé.

Beaucoup d'entre eux se demandent: pouvez-vous remplacer le bouton-poussoir Démarrer par la clé? Il s'agit d'une demande assez en difficulté, et en général, il est impossible de mettre en œuvre une tâche aussi compliquée.

Dans cet article, nous donnerons une explication détaillée du principe de cet élément et pourquoi nous ne pourrions pas le remplacer par une clé.

Pouvez-vous remplacer le bouton-poussoir Démarrer par la touche?

Par conséquent, il sera difficile de rechercher un mécanicien professionnel pour effectuer de telles tâches paradoxales.

Comment choisir le démarrage de poussée compatible?

Before changing key ignition to push button , it is vital that you pick up a compatible keyless system for remote entry .

Since each vehicle is operated by a different type of ignition, you had better take it to garages or automotive shops to get instructions.

If you choose the button randomly, your vehicle will likely be ruined in a short term. Here are several things you should take into consideration:

  • Operating range: Given that every automatic start goes with a remote, you should also determine the specific active range of the remote. It will decide on the distance that you start your engine.
  • Cutoff switch: For your cars security, checking for the manual cutoff switch is necessary as it enables you to lock the engine at a distance.
  • The number of key fobs: Normally, the kit will have one fob; however, you will want to install it with more than one. Each key fob will represent one function. Also, these back-ups will be your lifesaver when you unfortunately drop the car key and dont know how to start the car without a chip key .

How To Install Push Start?

  • Step 1: Remove the steering wheel cover
  • Step 2: Check the voltage using a multimeter , and place the right pin on the harness and the other pin on the grounding point.
  • Step 3: After the voltage is checked, you mark the important wires needed to be connected to the button. It is advisable that you utilize the wiring diagram of your car.
  • Step 4: To keep you safe during the installation, we recommend you disconnect the electricity lines with a wrench.
  • Step 5: Attach the button to the right place.
  • Step 6: Connect the button with the corresponding ignition wires based on the instructions.
  • Step 7: Connect it with the brake wire and the antenna so it can receive the signals from a far distance.
  • Step 8: After the process is done, recheck the ignition systems operation to ensure it is still active.
  • Step 9: Close the steering cover and try out the new item.

Note: Since the installation requires a high accuracy level, you must do it step by step carefully. If you dont feel confident when implementing this process, you should take it to a professional mechanic.

Besides, these steps are not utilized in every type of car; therefore, observe before making a decision.

FAQ

Convenience: Some up-to-date car versions are installed with button kits that alert the drivers when they forget their fobs inside the car. This can reduce the risk of locking the car by yourself.

Réduisez les accidents: comme la voiture ne peut fonctionner que lorsque vous appuyez sur la pédale de frein et appuyez sur le bouton, il est beaucoup plus facile de contrôler la voiture pendant la conduite.

How Much Does It Cost To Convert Car To Push Button Start?

In terms of technical cost, the price range will vary depending on each type of button kit and whether you do it yourself or not.

On average, a button kit ranges from $25 to $150 ; the price could also be different for each type of transportation. Its advisable to buy it at an automotive shop or directly from your initial garage.

If you are a professional in fixing and can DIY, you only have to pay for the kits.

However, when you are new to these complex technical tools, youre better off taking it to a mechanic. The labor cost for button replacement is $100, depending on each shop.

How To Use The Push Start?

There are, of course, times when the key fob cant unlock your car , but fixing it is not much of a concern.

Conclusion

In conclusion, can you replace push button start with key?

It is impossible to switch from push button to key ignition due to the complexity and hefty expense of the task. Nevertheless, you can turn your conventional car into an auto-button vehicle.

You can do the installation yourself or take it to a garage. In principle, the auto button outweighs the traditional key because it is more secure and convenient.

If you find this information beneficial, please leave your comment below!